Buffalo Drivers Nintendo Wifi Usb Connector
Install Buffalo Nintendo WiFi USB Adapter driver for Windows 10 x64, or download DriverPack Solution software for automatic driver installation and update.
Just a different way of installing the nintendo wifi usb connector I'm sorry for the people who watched the. The Nintendo adapter is just a rebranded Buffalo Technologies Wireless G Keychain USB 2.0 adapter with a special driver to turn into into a wireless access point for the DS or Wii. The original Buffalo Drivers can still be downloaded here but installing them won't do you much good unless you make one.
Nintendo did a good job in realising that not everyone who has internet, also has a wireless home network. Teaming up with Buffalo, they released a USB device that shares the connection from an internet enabled PC to a DS or Wii. Many users have had problems, questions, and concerns, me being one of them. Well, I have spent countless hours playing with this thing, and I have solved most of the problems that I, and many others have experienced.
Usb Connector Registration Nintendo Wifi
First off, the device generates heat. A decent amount in fact.
Keep it in the open as much as you can. I have it hooked straight into the front USB port of my PC. If you are going to use the extension cord, find some way to prop it up.
The software that comes bundled with the device is officially out of date. Download the latest drivers there. (Actually, that's the whole setup wizard too.
You can throw the CD that comes with right in the trash.) 3. DO NOT insert the connector until you start the setup process. The wizard will tell you when to connect the device. The Wii does the rest for you. Just make sure you grant the Wii connection access from the manager in the taskbar.
For some reason the software finds it necessary to tell you when a a Wii or DS is connected or not. This is asinine considering the Wii constantly connects and disconnects during Wii Connect 24. To remedy this, you will have to either live with it, or disable Wii Connect 24. It is also important to understand that the in order to maintain a connection to the Wii, the computer that the USB Connector is connected to, must be on. Windows XP is the only supported platform so far.
Although dial up users have reported shakey success, I would not recommend using the Connector with anything but a high speed connection. Nintendo forums FAQ: I only recommend using the official software and drivers if you do not use Wii Connect 24, only use Nintendo Wi-Fi occasionally, or simply do not wish to use anything but the official software and drivers. I am using modified Buffalo drivers, and Asus software, in turn making the connector a bonifeid wireless adapter. I would suggest anyone not afraid to do so, does this. The tutorial will be posted below.
Note: I did NOT write this tutorial. I have reposted it from another website with the permission of the author. This tutorial will teach you how use the Wi-Fi adapter as a SoftAP, giving it the same capabilities as a wireless router. Download this rar file: Then follow these steps: 1: If you want to use the official Nintendo Wi-Fi USB Connector as a standard SoftAP make sure you have removed the Nintendo software and drivers as they will no longer be needed.
2: Inside the Drivers folder of the RAR file, you will find modified Buffalo drivers. Install these drivers for the USB Connector. Then install the ASUS software (also in RAR file(eng2371.zip)). When it prompts you to restart, select No. I have found that there is no need to. 3: Now in the ASUS EXEs folder of the RAR file, extract the six EXE files in the into the ASUS folder (C: Program FilesASUSWLAN Card Utilities). Make sure you overwrite the existing files.
4: Then click Start - All Programs - ASUS Utility - WLAN Card - ASUS WLAN Control Center. You will get a dialog asking if you want to use the Windows configuration utility or the ASUS one, select the option that uses ASUS one and disables the Windows one. Then there will be a wizard. Click Cancel to close the wizard. 5: Now copy the file (C: Program FilesASUSWLAN Card UtilitiesDriverWinXPAPrt2500usb.sys) to (C: WINDOWSsystem32drivers). Make sure you overwrite the existing file.
6: Right-click on the ASUS software icon in the System Tray (bottom-right corner of screen) and select Wireless Settings. When the settings dialog opens, on the left select Config, then go to the SoftAP tab, and select Soft AP Mode.
Then un-tick the Enable ICS checkbox. Then on the left click Apply. You will get a message box asking if you really want to change to SoftAP mode, click Yes. A message will come up saying something like 'add the adapter to the network bridge', just ignore it and click OK. If all has gone well, there will be no error messages. Now close the ASUS Wireless Config utility or it will start conflicting when we manually set ICS. 7: Now go to Control Panel - Network Connections (this may have opened automatically opened up when you Applied the SoftAP settings).
Right-click on the Network Adapter you are currently accessing your Internet through (or your internet connection icon) and open the properties for that connection. Go to the Advanced tab, and click 'Allow other network users to connect through this computer's Internet connection'. Then click OK. If you get an error message saying the IP address is already in use, disable the Network adapter you are trying to share then try again - be sure to enable it again afterwards. It can take a long time for ICS to be enabled so wait patiently. 8: Now right-click on the Wireless Network Connection and click Properties. In the middle of the dialog there will be some protocols, select Internet Protocol (TCP/IP) and then open the properties for that.
Windows would have assigned a static IP address if ICS was successfully enabled, check to make sure this IP address does not conflict with other IP addresses on your network. Also, it should be on a different subnet to the Local Area Connection (for example, my computer's IP address is 192.168.0.2, I assigned the wireless network connection the IP address of 192.168.1.1 - which is on a different subnet). If it is on the same subnet, ICS will not work correctly.9. With that done, open the ASUS Wireless Config utility again.
On the left select Config, in the Basic tab set a SSID. In the encryption tab, select Shared for Network Authentication and WEP for Data Encryption - I have found that this works with the DS. Now enter a WEP key. Go back to the Basic tab, and at the bottom click on Advanced, change the 54g Mode setting to 802.11b only. Click Apply on the left to save the settings. 10: Now turn on your DS, play a Wi-Fi Connection game, go to the Nintendo WFC Settings, and select Manual Setup. Enter the SSID and WEP Key (both of these are case-sensitive) you entered to the ASUS Config utility before.
Select No to Auto-obtain IP Address (you must do this because the Nintendo DS doesn't seem to DHCP correctly with ICS for some reason). Now give your DS an IP Address (this must be on the same subnet as the USB connector, I gave my DS the IP address: 192.168.1.2). For subnet mask enter 255.255.255.0. For gateway and primary DNS, enter the IP address of the USB connector.
Now try and test connection, and if all has gone well the connection should be successful! 11: Now with the ASUS Wireless Config utility, hide your SSID, and use MAC Address filtering to improve the security of your Wireless access point. 12: You now have an Official Nintendo Wifi USB Connector that can connect online with any other devices.Keep in mind that the Wi-Fi Connector now has the same capabilities of a wireless router, and it is possible to connect multiple devices to the internet wirelessly. I used to use it on my DS Phat and I had a ton of issues.so then I got a wireless router.it works great. Don't get me wrong, I think this thread is very well constructed, and people should use it to their full advantage.I'm just saying that the router has made things much easier. DSfanaticIn some cases the router is better.
For example, if you already have a wireless network, there is no need for the Connector. But in my case, I only have one computer and no other devices that connect to the internet. A router would not be ta smart investment considering it would be used solely for the Wii and DS. However, since I am using the modifeid drivers, if I do get a device that uses Wi-Fi technology, the USB Connector will alow me to do so. Once you tap into the capabilities of this thing, it's pretty handy.
Finally I can dispose of my Windows XP partition. Recently, I decided to try one of the many work arounds to try and get our Nintendo Wi-Fi USB Connector working in Vista. I’d tried before, but had very little success to say the least. As a last resort, I visited the Nintendo download section. I say visited, what I really mean is trawled through millions of pages trying to find the actual download page.
I am quite amazed that Google didn’t find it with terms such as “WiFi Vista Nintendo” and “Nintendo WiFi Driver”. Anyway I eventually found the page I was looking for. And it had been updated! Nintendo have finally updated the software to work on Windows Vista.
I knew the software wasn’t going to be too great, but I had nothing to lose so gave it a shot. I have to say -it works much better now. This version features the following upgrades/corrections from version 1.05:. Reduction of CPU load when the Nintendo Wi-Fi USB Connector is not connected. Changes to certain registration tool message displays. Added Windows Vista compatibility. Change to specification that requires the Nintendo Wi-Fi USB Connector to be attached when uninstalling.
Nintendo Wi-Fi USB Connector version 1.06 – Install Instructions! You MUST uninstall any previous versions of the software.! You MUST have the Nintendo Wi-Fi USB Connector plugged in during the uninstall. For complete setup instructions: Wii: DS: For troubleshooting, go to: Download the Latest Software for the Nintendo Wi-Fi USB Connector If you already have successfully installed the Nintendo Wi-Fi USB Connector and are able to connect your Wii console online, there is no need to download or install another version of the software. There is no benefit to doing so, and it is not recommended for those who currently have a working connection. Important! Previously-installed versions of the software must be uninstalled prior to updating with a newer version.
For help uninstalling. Remember to reboot your PC after the uninstallation process, before installing another version! Available Software Versions: (For assistance with downloading and installing the software, please see the information at the bottom of this section.) Windows 7 users: There is no installation software available for Windows 7, and we cannot guarantee that any of the available versions will work with Windows 7. No Note: Depending on how your version of Windows XP or Windows Vista is configured, the steps below may vary slightly from your setup. You also may be prompted by Windows XP or Windows Vista to allow the download or installation of the software with a warning that Windows XP or Windows Vista does not recognize it. It is safe to allow the download. Click on the version number of the software you wish to obtain from the section above.
You will then be prompted to either “Open/Run” or “Save.” Click “Save” and use the drop down in the save menu to save the file to your desktop. Once the file has downloaded, go to your desktop, and right click on the.zip file (NintendoWFCUSB.zip) that just downloaded, and click on “Extract All”. Click “Next” and then click “Next” again to extract the files to your desktop. Click “Finish”; a new folder with the extracted files should now be on your desktop.
Click the new folder to find another folder called “NintendoWFCReg.” Click this folder to see its contents. Scroll down the list of files to find “Setup.exe” and double click this file to begin the installation process. Shiro can we talk rar download. (For step-by-step assistance with this process, please.) In order to work with Windows Vista, you must have version 1.06 or higher of the Nintendo Wi-Fi USB Connector software (available above). Windows 7 users: There is no installation software available for Windows 7, and we cannot guarantee that any of the available versions will work with Windows 7. Important: The Nintendo Wi-Fi USB Connector has been discontinued until further notice.
As an alternative for on-line access, Nintendo DS owners can use a standard wireless router or Hotspot location. Please for more information. What is the Nintendo USB Connector? The Nintendo Wi-Fi USB Connector is a Nintendo-dedicated wireless access point that plugs into the USB port on a PC (Windows XP or Windows Vista. only). Important: The Nintendo Wi-Fi USB Connector has been discontinued until further notice. As an alternative for on-line access, DS owners can use a standard wireless router or Hotspot location.
Please for more information.In order to work with Windows Vista, you must have version 1.06 or higher of the Nintendo Wi-Fi USB Connector software. To download the latest version. Do I have to buy the Nintendo Wi-Fi USB Connector? Absolutely not!
If you already have a wireless router in your home, you will be able to use your Nintendo DS to connect online and play games. If you do not have a wireless router, you can buy one at your local retailer. For more information.
If you do not wish to setup a wireless network in your home, you can also connect to the Nintendo WFC at many Hotspots. For more information on setting up a connection at a Hotspot,. Important: The Nintendo Wi-Fi USB Connector has been discontinued until further notice.
As an alternative for on-line access, Nintendo DS owners can use a standard wireless router or hotspot location. Please for more information. In order to use the Nintendo Wi-Fi USB Connector you will need the following: What do I need to be able to use the Nintendo Wi-Fi USB Connector?.
Broadband internet connection. Nintendo DS system. PC running Windows XP or Windows Vista. with active internet account. Nintendo Wi-Fi Connection compatible Nintendo DS game.In order to work with Windows Vista, you must have version 1.06 or higher of the Nintendo Wi-Fi USB Connector software.
To download the latest version. Important: The Nintendo Wi-Fi USB Connector has been discontinued until further notice. As an alternative for on-line access, Nintendo DS owners can use a standard wireless router or Hotspot location. Please for more information. Where can I buy the Nintendo Wi-Fi USB Connector?
The Nintendo Wi-Fi USB Connector has been discontinued until further notice. As an alternative for on-line access, Nintendo DS owners can use a standard wireless router or Hotspot location.
Please for more information. How do I uninstall the Nintendo Wi-Fi USB Connector software? Please follow these steps on your computer to remove the Nintendo Wi-Fi USB Connector software:.
Uninstall the USB connector through the Device Manager. Make sure you have the USB Connector plugged into your computer.
Click the Start button and select Control Panel. Click “System” and select the “Hardware” tab. Choose “Device Manager.”. Next to “Network Adapters,” click the “+” to expand the list.
If the Nintendo USB Connector is in the list, right-click it and choose “Uninstall.”. Perform the DEVREMOV process. Make sure you have the USB Connector plugged into your computer.
On your computer, click on the “My Computer” icon (found in the Start menu or sometimes on the desktop), and right click on your CD drive containing the Nintendo Wi-Fi connection Installation CD, and choose ‘Explore.’. Open “NintendoWFCReg/SoftAP.” Within there, double-click the DEVREMOV.exe application. During the course of running the DEVREMOV program, you will see three windows pop up successively. The first will have a series of question marks.
Click “Yes.”. The second will have a picture of wires and lights moving on it while the DEVREMOV utility uninstalls the internet connection sharing for the Nintendo Wi-FI USB Connector. This will disappear on its own. The third will also have several question marks on it.
Just click “Ok.”. At this point, remove the USB connector from your computer. Check the “Programs” list and, if the “Uninstall” option for the connector is there, run this process. Click the Start button, and select “Programs.”. If the Nintendo USB Wi-Fi Connector is listed, click on the “Uninstall” program to remove it. Check Add/Remove Software on the computer and, if listed, remove the USB connector.
Click the Start button, and select Control Panel. Open “Add/Remove Programs.”.
If listed, select the Nintendo Wi-Fi connector from the list, and click “Remove.”. Follow the prompts to uninstall the program. Reboot your computer to complete the uninstallation. Download: Nintendo Wi-Fi USB Connector XP/Vista Driver Version 1.06/1.07!!!
MD5: F288BCEEA75F76C2B1AEDBD80789A15B. No More Goat Soup wrote a fantastic post today on “Nintendo Wi-Fi USB Connector XP/Vista Driver Version 1.06 (10/22/07)”Here’s ONLY a quick extract com/consumer/systems/wii/enna/connectingOnline. Jsp?entryId=usbInstall DS:. You MUST have the Nintendo Wi-Fi USB Connector plugged in during the uninstall.1. The uninstall can be found in your Programs list in the “Nintendo Wi-Fi USB Connector” folder.2. Run the “Uninstall Nintendo Wi-Fi USB Connector Registration Tool” click OK. The WiFi driver has always worked for me.
There could be issues arising from Driver Signature Enforcement, for some people. Start/Programs/Accessories – Right-click “command prompt” and select “run as administrator” – At the command prompt, type bcdedit /set loadoptions DDISABLEINTEGRITYCHECKS – Reboot! Or maybe try the easier way: Before Windows Vista loads, press F8 (like you would do to enter safe mode) Using the F8 option. An F8 Advanced Boot Option introduced with Windows Vista—“Disable Driver Signature Enforcement”—is available to disable the kernel-signing enforcement only for the current boot session. This setting does not persist across boot sessions. Maybe uninstall it, reinstall it with Driver Signature Enforcement disabled.
Sorry, but the only ideas I have. Like I said, it’s always worked fine for me when I install. Hope it works!
Whether you’re using the Nintendo Wi-Fi USB Connector, the Wii LAN Adapter, or a wireless router, firewalls and other computer security programs can be very tricky to get working when attempting to do online gaming. Anti-virus, anti-spyware, software firewalls, and firewall-enabled routers can affect communications within your network. You may want to consider temporarily disabling, or removing, these products installed on home networks to enable game play. If this is not the approach you wish to take, below are some guidelines for how your firewall or security program needs to be adjusted. As each manufacturer is different, if you need help making these adjustment, please contact your firewall or security program manufacturer. The following detailed information regarding required protocols, ports and communication requirements needed by the Wii console, games, and the Nintendo Wi-Fi USB Connector (if used) may be helpful.
Please consult your firewall’s instruction manual or manufacturer for specific assistance on working with the firewall. While Nintendo makes a concerted effort to test and document known incompatibilities with software and hardware, it is impossible for us to test and document them all. Detailed information regarding the necessary ports and sites has been included below for those customers who want to use and configure their own firewall or computer security application. Allowing TCP and UDP Traffic: The Wii console may require unrestricted access to several sites across various ports and protocols to function correctly.
These addresses and ports vary, and may change in the future without notice. Many software firewalls restrict outbound access. Only if your firewall blocks outbound traffic do you need to enable this traffic: TCP: Allow traffic to all destinations on ports: 28910, 29900, 29901, 29920, 80, and 443 UDP: Allow all traffic to all destinations.
(Necessary for peer-to-peer connections and game play). Our Network Test tool can be used from a computer behind your firewall to test if outbound UDP is allowed. Please note that by allowing the traffic to the destinations listed above, you are essentially removing a significant amount of firewall protection for your network. While Nintendo provides this information for our consumers’ use, it is up to each consumer to determine what security needs they have for their own networks, and to decide how best to configure their network settings to meet those needs. Additional Information for the Nintendo Wi-Fi USB Connector Users If you are using the Nintendo Wi-Fi USB Connector, and have a software firewall or other computer security program installed on your computer, there may be additional steps you must complete to allow a successful connection. “Trusted” Applications: If your firewall or PC security program keeps a list of trusted applications (also known as a “trusted zone”), the following programs are installed with the Nintendo Wi-Fi USB Connector, and require internet communications. If prompted by your firewall or PC security program, add these to the list of trusted applications.
This information may also apply to certain computer security applications, such as anti-virus, anti-spyware, etc.: Nintendo Wi-Fi Connector USB (NintendoWFCReg.exe ) Setup.exe (when installing the USB Connector) SoftAPInstDrv.bin mdriver.exe “Trusted” IP Ranges: There are also potential ranges of IP addresses that may need to be added to the “trusted zone” for your software firewall or PC security program for Nintendo Wi-Fi USB Connector users. Each of these would need to be opened up for TCP and UDP traffic, or for some firewalls or security programs, added as a “trusted zone.” Please consult the manual for your firewall or security program for more specific information. 192.168.1.1 subnet mask 255.255.255.0 172.16.1.1 subnet mask 255.255.255.0 0.0.0.0 subnet mask 255.255.255.255 Software Firewalls Identified as Being “Incompatible” with the Nintendo Wi-Fi USB Connector We have identified the following software firewall(s) as being incompatible with the use of the Nintendo Wi-Fi USB Connector.
We suggest using another firewall product, if possible: Zone Alarm Internet Security Suite Important Note: In order to use the Nintendo Wi-Fi USB Connector, Zone Alarm Internet Security Suit must be completely uninstalled from your computer. Simply disabling (turning off) this program will still not allow a successful connection. Turn off any “VPN” programs running on the computer Virtual Private Network (VPN) programs can interfere with the Nintendo Wi-Fi USB Connector, and must be turned “off” or “disabled.” VPN’s are typically found on computers belonging to those who need to create a secure connection to an outside network (for example, people who work from home).
Installation Help for the Nintendo Wi-Fi USB Connector Before Beginning: The information on this page can be used for troubleshooting the Nintendo Wi-Fi USB Connector installation process. Important Note: If you received the “Grant Permissions” screen of the installation tool, then the installation was successful. If your installation was successful and you are able to connect your Wii console, but are not able to stay connected or are receiving an error code, it may be caused by a firewall or anti-virus issue. Please click here for more information. If during the Nintendo Wi-Fi USB Connector installation process you are unable to get to the “Grant Permissions” screen, then the following troubleshooting on this page may help get the installation completed. The steps below are performed on your PC, or if/when necessary, your router. Note: If you have a network setup where one computer with a modem is being used by other computers to access the internet, the USB connector should be installed on the computer with the modem.
Does the Setup CD automatically start when you insert it into your computer? If the Setup CD does not automatically start up when inserted, the Autorun feature of your computer may not be enabled. If the set up window doesn’t appear, on your computer, click the “Start” button, choose “Run,” and then click the “Browse” button. Click on the CD drive the Setup CD is in and locate the Setup.EXE file. Double-click this file to begin the installation process.
Ensure that you have rights to install software on the computer Windows XP only allows users who are granted “Admin” rights in their profiles to install software. This includes the software necessary to install the Nintendo Wi-Fi USB Connector.
To determine if the profile you are using has “Admin” rights: Click the Start Button and select the Control Panel. Select “User Accounts.” A list of all User Accounts are displayed. Users listed as “Administration” level are able to install software. If the profile you are using does not have these rights, you will not be able to install the required software.
Please contact an individual with “Administrator” settings for assistance. Make sure you have the most current install software to check our Nintendo Wi-Fi USB Connector software downloads page. Upgrading to the most current software may solve some installation and connection issues. (Note: if you already have Nintendo Wi-Fi USB Connector software installed, be sure to uninstall and reboot your computer before installing another version.) Check to see if there might be an IP Address conflict between the router and the USB connector: Verify your Default Gateway IP on your computer: Click the Start button Click “Run.” Type CMD and click Ok.
The Command Prompt (small box with a black background) will appear. After c: type IPCONFIG/ALL and press Enter. Your Default Gateway IP will now be displayed. If the Default Gateway displayed is either 192.168.0.1 or 192.168.1.1, you will need to find the IP Address in you router’s settings and change it to 192.168.2.1 Important!
If you have any other devices that utilize the router, you will need to update the IP Address on each of these to match the one you entered on the router. If the IP Address needed to be changed, power down your computer and, if you have not already done so, disconnect the USB connector. Being sure to leave the connector disconnected, power on the computer and go through the installation process again. If the IP Address does not need to be changed, or if the installation fails, please keep reading. Check Local Area Connections to determine what the Internet Connection Sharing (ICS) options are set to.Which option is correct will depend on how you have your computer set up. Unless indicated otherwise, make sure the USB connector is connected to the computer throughout these steps.
To perform the following steps, you will need to access your computer’s Local Area Connection screen. To do this, click the Start button, select Control Panel and click on the Network Connections option.
Adjust the ICS options as needed: If one Local Area Network is listed on the Local Area Connection screen, other than the USB Connector: Right click on that connection, select Properties, and then the Advanced tab. If the ICS options are enabled, uncheck all boxes under the ICS area to disable them. If the ICS options are disabled, check all boxes under the ICS area to enable them. If two or more Local Area Networks are listed on the Local Area Connection screen, other than the USB Connector: Right click on the “Network Card,” select Properties, and then the Advanced tab. Uncheck all boxes under the ICS area to disable them.
(If you are getting an Internet Connection Sharing error, the ICS settings were most likely enabled (checked).) Uninstall the USB connector through the Device Manager. Make sure you have the USB Connector plugged into your computer. Click the Start button and select Control Panel.
Click “System” and select the “Hardware” tab. Choose “Device Manager.” Next to “Network Adapters,” click the “+” to expand the list. If the Nintendo USB Connector is in the list, right-click it and choose “Uninstall.” Perform the DEVREMOV process.
Make sure you have the USB Connector plugged into your computer. On your computer, click on the “My Computer” icon (found in the Start menu or sometimes on the desktop), and right click on your CD drive containing the Nintendo Wi-Fi connection Installation CD, and choose ‘Explore.’ Open “NintendoWFCReg/SoftAP.” Within there, double-click the DEVREMOV.exe application. During the course of running the DEVREMOV program, you will see three windows pop up successively. The first will have a series of question marks. Click “Yes.” The second will have a picture of wires and lights moving on it while the DEVREMOV utility uninstalls the internet connection sharing for the Nintendo Wi-FI USB Connector.
This will disappear on its own. The third will also have several question marks on it. Just click “Ok.” At this point, remove the USB connector from your computer. Check the “Programs” list and, if the “Uninstall” option for the connector is there, run this process.
Nintendo Wifi Usb Connector
Click the Start button, and select “Programs.” If the Nintendo USB Wi-Fi Connector is listed, click on the “Uninstall” program to remove it. Check Add/Remove Software on the computer and, if listed, remove the USB connector. Click the Start button, and select Control Panel. Open “Add/Remove Programs.” If listed, select the Nintendo Wi-Fi connector from the list, and click “Remove.” Follow the prompts to uninstall the program. Remove the installation CD, power down your computer, and disconnect the USB connector if it is still connected.
Being sure to leave the connector disconnected, power on the computer. Once the computer is on, plug the connector into the USB port. If Windows XP does not detect the connector as a new device and prompt you to install it, all components have not been removed from the computer.
Complete steps 2 through 5 again. If Windows XP does detect the connector as a new device, remove the connector from the USB port and go through the installation process again. If the installation is still unsuccessful: There are likely settings on your computer that are making it incompatible with the installation program. Please call 1-800-255-3700 to discuss additional options. I’m running Vista Home Premium SP1, on a Acer computer. My Internet connection is MTS. I’m using a stick that came with v1.05, I’m not using that v.1.05 disc, and I’m downloading it with v.1.06 download link you gave out.
I tried about 5 times. Everything goes fine when it’s installing, I do everything it tells me to do. When it gets to the stage where it is setting up the Connection Sharing or whatever, My Internet connection goes away and doesn’t come back ’till I restart.
I restart and my Internet is back, but Wi-Fi is not installed. (It’s ether error 5, or 6 when my Internet goes away) Please E-Mail me if you, or anyone reading this has any advice. I also had Internet Connection sharing error 6 until I gathered up a bunch of tips from different sources, Install as per usual and get the error and leave the wifi usb connector in. Go to control panel, network and internet, and then network and sharing center. Whatever is your main source of internet hit view status. Then hit properties and the sharing tab. Make sure allow other users to connect is checked.
If you have problems still then go to windows firewall and activate it. I did the first steps dozens of times to no avail but with the firewall up it was suprisingly simple. Write back if this helps out any. Hi I download the files fine and install everything correctly and connect my ds to the computer. But when i get to stage 3 of the wifi config the connection works perfectly with the green icon but then after about 15 seconds goes red and comes up with,” error code 52003, unable to find IP address,”. So i try uninstalling all of the spyware and firewalls and antivirus programs but nothing seems to work so i try to do it manually but i do not have an SSID or a gateway or a DNS. I have looked all over the web but nothing works so is it something wrong with the USB or is there something i am forgetting.
Hope you can help thanx. Goat’s top tip: Tried “Disable driver signature enforcement”? Reboot and press the F8 key immediately after BIOS POST. You will be presented with several options for booting Vista. One of the options will be to disable driver signature enforcement.
Select that and then try installing again. Keep an eye out for little red “pop up” dialogue boxes. They often get hidden behind other windows I bet it’s that but failing that the only things I can think of are: Have you have tried without firewall? If you’re using Window’s firewall perhaps unplug your internet connection and try without it running.
Try installing again. Also you could try going into the subfolder named “SoftAP” and running DEVREMOVE.exe to clean the device install and start again. Also you could try manual inf install. Navigate to the location where you extracted the install files. Xxxxx NintendoWFCUSB NintendoWFCReg U2G54 WinVista Find the file called rt25usbap.inf and right click it, “Install”. Vista should now accept the device, but you’ll still need to get the installer to work for the ds to work.
I have the same error than Matt (2008 november 27). Vista 32-bit home premium, a lot of people over the internet had this error recently. Matt exactly told how the DS would react before the error window pops in I have a DS original by the way: It is error code 52103 (when IP for either your internet or Nintendo WFConnector connection isn’t set to “Obtain IP automatically”) or 52003 and the only solution I know is to re-install the software, reboot after installation, and there you have it, but you will need to do this everytime because after another reboot it won’t work anymore! On the NDS it says “Unable to obtain IP Address. Confirm that the Nintendo Wi-Fi Connector is functionning properly. For help, visit blablabla and your firewalls/antiviruses are turned off. Hey, nomoregoatsoup, thank you so much for your support to all of us gamers here.
I am using vista ultimate 64 bits, and I´m pluging my usb wifi connector everywhere in all of the usb connectors. Even so, the device doesn´t get to install the software at all. All though I had previously used in windows XP sp2 with no problems at all, i´ve upgraded to vista only to ifnd out I don´t know how to run this thing now. The wifi usb connector isn´t activating any lights when plugged in the machine either.
I´ve followed everything you said inhere. Could the fact that´s a 64 bit be the reason? If so, I already tried the run in windows vista xp sp2 compability mode while running the installation app as administratorbut it simply refuses to run. My error says: “no device connected” – and it is connected. Then it says: Software error – not installed.
Sadly, I’m unable to confirm if the adapter works in Vista 64bit. I never got to try the Wi-Fi connector in x64. I was using 32bits at the time, and now I have a really ugly Wireless N router instead. As you can probably see from the comments above, many people have trouble with x64 and N-WFC. To make matters worse; Nintendo say it works with Vista -but don’t say which type they tested it on. You know they’re all too busy playing Wii-Sports to worry about technical details.
Hmm there was a way to turn the USB adapter into a standard buffalo wireless adapter tho I wonder if that would help x64 users.? Might be worth a shot.
First off, I’ll say props to you goat for being so patient with the less computer savvy users here. I know this ain’t any easier for you.
Second, I’d like to throw my own hat into the ring. I had Windows Vista (presumably 32 bit) home premium. Though I had issues at first getting the cd installer to work, for some reason it was able to bypass the “wrong OS system” error through sheer will (‘just kept clicking I guess) and it worked like a charm. Then that computer died becase BIOS failure and blah blah blah. I’ve bought a new computer, a Windows Vista Ultimate SP1, but I haven’t gotten that error this time. Rather, the setup screen will either freeze in place while installing the drivers (the cd installer) or popup an error in the last 1% of the installation asking to connect the USB (“OK” being the only option) and immediately showing the installation bar 100% saying “Application Error”.
Nintendo Usb Wifi Adapter
The computer can’t locate the driver either through the CD, the zip file, or the buffalo hack you linked me to by itself. I’ve tried disabling firewall/virus protection McAfee, couldn’t access “Driver Signature Enforcement” (there IS no F8, and F10’s setup had nothing on it), and DEVREMOV did nothing for me. Any other suggestions you may have? It’s a brand new computer 😦 Thanks for the help. I did everything as should be.
I started to run the setup.exe, so it brings up a small window that loads quickly and disappears, as should be then brings up another window that loads some, then asks me to insert the Nintendo Wi-Fi USB Connector. And it continues to load.
It starts to set up Internet Connection Sharing, but a new window comes up with a message, and I quote, “Internet Connection Sharing error.(5)” I hit OK and it totally stops. And it didn’t complete the installation. Windows Vista Users! Turn off your anti virus programs.
1) Once it downloaded go into it via winrar then go into it untill u get to NintendoWFCUSB then extract it by right clicking to your desktop 2) Once itd extracted then go into and scroll down untill u see setup. The right click and run as administration. It should run i had no issues yet installing it and i done it the way i just told you 5 times with success. 3) Once its installed then get your usb plug it in and run the WiFi Usb program. Hiiii previously I posted a question on this blog that.i needed the image file of the installation CD package for my sound card Sound Blaster Audigy SE(SB0570). Then the owner of this blog told me to download the installation CD rar file for Sound Blaster Audigy LS and also told me that Sound Blaster Audigy SE and Audigy LS are both sold under the same name Audigy LS. Accrording to him i did downloaded the installation CD.
But to my surprise, the software package wasnt getting installed at all as because the error said that “setup cannot find Sound Blaster LS on your PC, make sure your hardware is attached properly.” Soooo i would request you to provide me with the installation CD for my sound card only that is Sound Blaster Audigy SE(model number: SB0570). Thanx in advance.
I together with my guys were found to be digesting the excellent items located on your web blog then before long developed a terrible feeling I had not thanked the web blog owner for them. My people appeared to be certainly excited to learn all of them and have now seriously been having fun with these things. Appreciation for simply being considerably considerate and also for having certain fine ideas millions of individuals are really desirous to know about. Our own honest apologies for not expressing gratitude to earlier.